A good used car inspection has three parts: paperwork checks before you travel (a PPSR search, recalls and service history), an OBD2 scan that shows stored fault codes and whether codes were recently cleared, and a careful walk-around and test drive. Then, for any car you're serious about, book an independent pre-purchase inspection.

Before you see the car: paperwork checks
Run a PPSR search
The Personal Property Securities Register (PPSR) is the official government register run by the Australian Financial Security Authority. A PPSR car search at ppsr.gov.au uses the car's VIN (vehicle identification number) and tells you:
- whether money is owed on the car and a lender has registered an interest over it
- whether it's been recorded as written off
- whether it's been reported stolen
- registration details, plus the make, model and colour on record
If a lender has an interest registered and the seller stops paying, the lender may be able to repossess the car even after you've bought it. A "statutory write-off" result means the car was damaged badly enough that it can't legally return to the road. Ask the seller for the VIN before you go, run the search, and check the details match the car in the advert. Run it again close to the day you pay, because finance can be registered at any time. Keep the search certificate.
Use the official ppsr.gov.au site. WA Consumer Protection warns that some unofficial sites link to the PPSR and charge much more for the same search.
Check for Takata and other recalls
Check the car against the Takata airbag recall list at productsafety.gov.au/takata, or enter the plate and state at ismyairbagsafe.com.au. Replacement of an affected airbag is free, but you want it done before you buy, not after. You can also ask a dealer for that brand whether any other recalls are outstanding on the VIN. Our ABS and airbag warning light guide covers what an airbag light means.
Ask for the service history
Ask for the logbook and receipts. Look for regular servicing at sensible intervals, and check that the odometer readings in the logbook climb steadily. A reading that goes backwards, or a long gap with no records, needs an explanation. WA Consumer Protection notes that the average Australian driver covers about 12,000 to 15,000 km a year, which gives you a rough guide for whether the odometer suits the car's age.
Scan before you buy: what an OBD2 scan shows
Most petrol cars sold new in Australia from 2006, and diesels from 2007, have an OBD2 diagnostic port, usually under the dash on the driver's side. A scanner plugged in there shows what the engine computer knows, which a seller can't easily hide. Ask the seller's permission first. A seller who refuses a scan is telling you something.

Readiness monitors: the sign codes were just cleared
This is the most useful check a buyer can do. Clearing fault codes turns off the check engine light, but it also resets the car's readiness monitors. These are self-tests the engine computer runs on systems such as the catalytic converter, oxygen sensors and evaporative system. Each one shows as "ready" (the test has run) or "not ready" (it hasn't finished yet).
The New York DMV, which uses readiness checks in its emissions inspections, lists the common reasons for "not ready" monitors: codes cleared with a scan tool after repairs, a battery disconnected or replaced, a computer that needs a software update, or a pending problem that hasn't yet turned on the light. Monitors only become ready again after a specific mix of driving known as a drive cycle, which varies by make and model and usually takes more than one trip.
So if a car has been driven normally for weeks, most monitors should show ready. If several show "not ready", ask why. There may be an innocent answer, such as a new battery last week. Or someone may have cleared a fault just before the inspection, and the light will come back a few days after you've paid.
Fault codes and freeze frame
Read stored engine codes even if the check engine light is off. If a code is stored, the freeze frame data shows the conditions when it was logged, such as engine temperature, speed and load. Our guide to common OBD2 fault codes explains what the usual P codes mean. A code like P0420 (catalytic converter efficiency) or a misfire code in the P0300 range is a reason to negotiate or walk away until a mechanic has looked at it.
VIN and live data
On cars that report it, the scanner reads the VIN from the engine computer. It should match the VIN on the car's build plate, registration papers and PPSR search. With the engine running, live data lets you watch coolant temperature climb to normal operating temperature and stay there. An engine that never warms up properly, or runs hot at idle, needs a closer look.
How to scan a used car: step by step
- Ask the seller if you can plug in a scanner. Do it before the test drive, with the engine cold if possible.
- Find the OBD2 port and plug in the scanner with the ignition off.
- Switch the ignition on. Watch the dash: the check engine, ABS and airbag lights should all come on at key-on and go out once the engine is running. A light that never comes on at key-on may have been disabled.
- Read the VIN and check it against the paperwork.
- Read codes and note or photograph every one, including freeze frame data.
- Open the readiness (I/M) screen and note which monitors are ready and which aren't.
- Start the engine and watch live data: coolant temperature, idle speed and battery voltage.
- Don't clear anything. It isn't your car yet, and the codes are evidence.
- Scan again after the test drive. New codes sometimes appear once the engine is warm and has been worked.
A basic code reader only reads engine codes. It won't show ABS or airbag faults, so if one of those lights is on, treat it as a fault to be diagnosed before you buy. Our guide to using an OBD2 scanner covers the screens in more detail.
Walk-around inspection checklist
Inspect in daylight on dry, level ground. Rain and dim light hide paint and panel problems. The NSW Government's vehicle inspection checklist covers similar ground.
Body and exterior
- Rust in the sills, door bottoms, boot floor, wheel arches and under the carpets
- Paint that doesn't match between panels, overspray on rubber seals, and uneven gaps between panels, all signs of crash repair
- Hail dents on the roof, bonnet and boot lid, best seen at an angle
- Doors, bonnet and boot opening, closing and locking properly
- Cracks or chips in the windscreen
Under the bonnet (engine cold)
- Engine number and VIN match the registration papers, with no signs of tampering
- Oil level and colour on the dipstick. Milky or sludgy oil is a warning sign.
- Coolant level and colour, and no oily film in the overflow bottle
- Leaks, fresh oil spray, or an engine that's been degreased to suspiciously clean
- Battery terminals free of heavy corrosion
- Smoke at start-up. Blue suggests oil burning; thick white smoke that doesn't clear may mean coolant.
Tyres and underneath
- Tread depth on all four tyres and the spare. The NSW checklist suggests at least 5 mm.
- Uneven tyre wear, which can point to alignment, suspension or steering problems
- Oil leaks from the engine, gearbox, diffs, power steering and shock absorbers
- Exhaust leaks, holes or heavy rust

Interior
- Wear on the steering wheel, pedals and driver's seat that matches the odometer
- Seatbelts retract smoothly and buckle properly
- Air conditioning blows cold, and the heater works
- Windows, mirrors, central locking, wipers, horn, lights and indicators all work
- Damp carpet, water marks or a musty smell, which can mean leaks or flood damage
Test-drive checklist
Confirm the car is registered and insured before you drive it. Then:
- Start the engine yourself from cold. Listen for rattles, knocks or slow cranking.
- Check every warning light goes out after start-up.
- Drive at low speed with the window down and listen for clunks over bumps and clicks on full lock.
- Brake firmly in a safe place. The car should stop straight, without pulling, juddering or a soft pedal.
- Check the steering is straight and doesn't wander at highway speed.
- Run through every gear. Automatic shifts should be smooth with no flare or slip. A manual clutch shouldn't slip or bite right at the top.
- Get the car to highway speed if you can, and watch the temperature gauge stays steady.
- After the drive, park and check for new leaks, smells or smoke, then scan again.
Extra checks for 4WDs and tow vehicles
- Engage four-wheel drive (and low range, if fitted) and check it goes in and comes out cleanly
- Look under the car for dents or scrapes on the sump, fuel tank, diffs and chassis rails
- Look for mud, sand or silt in odd places, such as behind trim panels or in the spare wheel well, which can point to deep water crossings
- Check the towbar and wiring for heavy use, and ask what has been towed and how often
- Check aftermarket accessories such as lift kits, bull bars and long-range tanks. Ask for paperwork, because some modifications need approval and can affect registration and insurance.
- On diesels, ask about DPF regeneration and look for DPF-related codes in the scan
Roadworthy and safety certificates: how the states differ
Each state and territory sets its own rules. Here's the broad picture for the three largest states:
| State | Certificate | When it applies |
|---|---|---|
| Victoria | Roadworthy certificate (RWC) | A private seller of a registered car must give the buyer an RWC no more than 30 days old. |
| Queensland | Safety certificate | Needed before a registered vehicle changes hands, except when sold to a dealer. Issued only by approved inspection stations. |
| New South Wales | Safety check (pink slip) | Most light vehicles more than five years old need a yearly safety check to renew registration. |
Western Australia, South Australia, Tasmania, the ACT and the Northern Territory each have their own rules for inspections at transfer, re-registration or renewal. Check with the transport agency in the state where the car will be registered.
Most importantly, none of these certificates is a full mechanical inspection. The Queensland Government says a safety certificate checks basic safety items such as tyres, brakes, steering, suspension, body rust, windscreen and lights, and is not a comprehensive inspection of the vehicle's quality or life expectancy. Consumer Affairs Victoria describes an RWC as a general safety check. A certificate tells you the car met minimum safety standards on the day. It tells you nothing about the gearbox, the turbo or how long the engine will last.
For that, book an independent pre-purchase inspection through a motoring club such as the RACV, NRMA, RACQ or RAC WA, or a qualified mechanic you trust. Show them your scan results. Also keep in mind that WA Consumer Protection notes buying from a private seller is at your own risk, as consumer guarantees and statutory warranties don't apply to private sales.
Red flags: when to walk away
- The PPSR shows finance owing, a write-off or a stolen record
- The seller won't let you scan the car or book an independent inspection
- Several readiness monitors show "not ready" with no believable explanation
- The VIN on the car doesn't match the papers or the PPSR search
- Warning lights stay on, or never come on at key-on
- Odometer readings in the logbook don't add up
- An outstanding Takata airbag recall the seller won't fix before sale
Which Autophix scanner do you need?
For a pre-purchase scan, you need a tool that reads engine codes, freeze frame and readiness monitors. All the Autophix code readers do that.
- OM123: a simple handheld that reads engine codes, live data, readiness, freeze frame and VIN. It needs no phone or app, so it's easy to take to an inspection. Covers Australian vehicles from 2006.
- OM127: the same as the OM123, plus JOBD support for Japanese-market imports with a 16-pin port.
- BT500 Pro: reads engine codes and adds a full battery, cranking and charging test, handy for checking whether a tired battery is behind a slow start.
- 3210Pro: a Bluetooth scanner with a phone app. It also reads ABS, airbag and transmission codes on some makes (Ford, GM, Chrysler, Toyota and Mercedes).

Be clear on the limits. The code readers read the engine only, so they won't show ABS or airbag faults. If you're buying a Toyota, Ford, Holden, Jeep, Mercedes-Benz or Nissan and want to see every module, look at the brand-specific and multi-brand professional scanners. For a side-by-side comparison, read our best OBD2 scanner in Australia guide.
Frequently asked questions
Can a seller hide fault codes before I inspect the car?
A seller can clear codes, which turns off the check engine light. But clearing codes also resets the readiness monitors to "not ready", and a scanner shows that. Several monitors not ready on a car that's supposedly been driven normally is a reason to ask questions.
What does a PPSR check tell me?
A PPSR car search, run with the VIN at ppsr.gov.au, shows whether a lender has registered an interest over the car, whether it's recorded as written off or stolen, and its registration and description details. Run it before you pay and keep the certificate.
Is a roadworthy certificate the same as a mechanical inspection?
No. A roadworthy or safety certificate is a check of basic safety items on the day. It doesn't assess the engine, gearbox or general condition. Book an independent pre-purchase inspection for that.
Do I need an expensive scanner to check a used car?
No. A basic code reader that shows engine codes, freeze frame and readiness covers the most useful pre-purchase checks. You only need a more capable scanner if you want to read ABS, airbag or other modules.
Should I still get a pre-purchase inspection if the scan is clean?
Yes. A clean scan means the engine computer hasn't logged a fault. It can't check rust, crash repairs, worn suspension or a tired gearbox. A mechanic can.