How to Use an OBD2 Scanner: A Step-by-Step Guide

A step-by-step guide to using an OBD2 scanner: finding the port, reading and recording codes, freeze frame, live data, readiness monitors and how to clear codes safely.

To use an OBD2 scanner, find the 16-pin diagnostic port under the dash on the driver's side, plug the scanner in, and turn the ignition on with the engine off. Let the scanner connect, then read the codes. Write every code and the freeze frame data down before you clear anything, then fix the cause.

Below is each step in detail: what the screen shows, how to read freeze frame, live data and readiness monitors, and how to clear codes without losing information your mechanic will need.

Before you start

You need three things: a scanner that suits your car, the car's build year and fuel type, and somewhere to write the results. A phone camera works well for that last one.

  • Check your car is OBD2. In Australia, Australian Design Rule 79/01 brought in European on-board diagnostic requirements for all new petrol light vehicles produced from 1 January 2006 and all new diesels from 1 January 2007. Many earlier cars have the port too. Japanese-market imports often use JOBD, which needs a scanner that supports it.
  • Park safely. Level ground, handbrake on, automatic in Park or manual in neutral. If you're on the roadside, get well clear of traffic first.
  • Don't run the engine in a closed garage. Most steps below need the engine off anyway. For live data with the engine running, open the garage door or work outside.
  • If the check engine light is flashing, stop. A flashing light usually means a severe misfire that can damage the catalytic converter. Pull over when it's safe and scan before you drive any further.

Not sure which tool you need? Our OBD2 scanner buying guide explains the differences.

Step 1: Find the OBD2 port

Close-up of a 16-pin OBD2 diagnostic port mounted in the lower dash panel of a car, with orange pin housing and wiring loom behind
A typical 16-pin OBD2 port, mounted low in the dash. Photo: 0x010C, CC BY-SA 4.0, via Wikimedia Commons

The OBD2 port (also called the data link connector or DLC) is a trapezoid-shaped socket with 16 pins in two rows of eight. The connector standard, SAE J1962, puts it on the driver's side of the instrument panel where it can be reached from the driver's seat. In practice that usually means under the dash, within reach of the steering wheel. In an Australian right-hand-drive car, start looking under the dash to the right of or just below the steering column.

Where to look:

  1. Sit in the driver's seat and look up under the dash, near your right knee and around the steering column.
  2. Check behind small trim panels or flaps under the steering column. Some are labelled "OBD" or "diagnostic".
  3. Look near the fuse panel cover at the end of the dash, or beside the centre console on the driver's side.
  4. If you still can't find it, check the owner's manual index under "diagnostic connector" or "data link connector".

A torch helps. On 4WDs and utes with aftermarket accessories, make sure you're plugging into the factory socket and not an accessory plug.

Step 2: Plug in the scanner

Line the scanner plug up with the port. The connector only goes in one way, because it's wider at the top than the bottom. Push it in firmly until it seats. Don't force it at an angle, as bent pins in the port are a common cause of "no communication" problems.

  • Handheld scanners such as the OM123 take power from the port, so the screen usually lights up as soon as it's plugged in.
  • Bluetooth scanners such as the 3210Pro plug into the port, then pair with the phone app.

Route the cable so it's clear of the pedals. Never drive with a handheld scanner hanging loose near the brake or accelerator.

Step 3: Ignition on, engine off

Turn the ignition to the "on" position without starting the engine. This powers up the engine computer so it can talk to the scanner.

  • Key ignition: turn the key two clicks to "ON", where the dash warning lights come on. Don't crank the engine.
  • Push-button start: on most cars, press the start button without your foot on the brake (or clutch) to reach ignition on. The exact sequence varies, so check the owner's manual.

All the dash warning lights should come on briefly as a bulb check, including the check engine light. If the check engine light doesn't come on at all during the bulb check, mention that to your mechanic.

Amber Service Engine Soon warning light glowing on a car instrument panel
The engine warning light goes by several names, including Check Engine and Service Engine Soon. Photo: IFCAR, Public domain, via Wikimedia Commons

Our check engine light guide explains what the light means when it stays on, and why a flashing light is different.

Step 4: Connect and read the codes

Autophix OM123 handheld OBD2 code reader
A handheld code reader such as the OM123 shows codes on its own screen, with no phone needed.

Choose the diagnose or OBD2 option on the scanner. It will try each communication protocol until it finds the one your car uses. There are five OBD2 protocols in use across different makes, and this step can take a few seconds. Then select "Read codes".

The screen will show a list of codes, each a letter followed by four digits:

  • P codes: powertrain (engine and transmission).
  • C codes: chassis (ABS, suspension).
  • B codes: body (airbags, comfort systems).
  • U codes: network communication between computers.

A code reader that reads the engine only will mostly show P codes, plus some U codes. If the second character is 0 (for example P0420), it's a generic code with the same meaning across makes. If it's 1 (for example P1xxx), it's manufacturer-specific, and you'll need the make's own definition.

You may see codes listed under different headings:

  • Stored or confirmed: the computer has confirmed the fault, usually after seeing it on more than one drive, and has normally turned on the check engine light.
  • Pending: the computer has seen a possible fault once but hasn't confirmed it. Pending codes are an early warning and may not have lit the warning light yet.
  • Permanent: some newer cars also keep permanent codes, which a scanner can't clear. They clear themselves once the computer confirms the fault is fixed.

Our guide to OBD2 fault codes explains the common ones, including P0420, P0300 to P0306 and P0171.

If the scanner won't connect

  1. Check the ignition is on.
  2. Unplug and refit the scanner, making sure it's fully seated.
  3. Check the cigarette lighter or accessory socket fuse. On many cars the port shares a fuse with it, and a blown fuse leaves the port without power.
  4. Check the car's build year and origin. An older car or a Japanese import may not use a protocol the scanner supports.
  5. Look at the port with a torch for bent or pushed-back pins.

Step 5: Record everything before you clear

This is the step people skip, and it's the one that matters most. Before you clear anything:

  1. Write down or photograph every code, including pending codes.
  2. Note the code descriptions as the scanner shows them.
  3. Open the freeze frame data and photograph each screen.
  4. Note the date, the odometer reading and what the car was doing when the light came on.

Clearing codes also erases freeze frame data and resets readiness monitors. If the fault is intermittent, the code you cleared might be the only record of it. Mechanics can use that record to diagnose the problem, and you can use it to show a pattern if the same code returns.

Step 6: Read the freeze frame data

Freeze frame is a snapshot of sensor readings taken at the moment the computer stored the code. It tells you the conditions the fault happened under. Typical values include:

  • Engine speed (RPM) and vehicle speed.
  • Coolant temperature, which shows whether the engine was cold or warm.
  • Engine load.
  • Short-term and long-term fuel trims.
  • Fuel system status (open or closed loop).

Freeze frame helps narrow things down. A lean code set at idle with a cold engine points somewhere different from the same code at highway speed with a hot engine. If you were towing a van up a long climb on a hot day when the light came on, the freeze frame will usually show high load and high temperatures to match.

Step 7: Look at live data

Autophix 3210Pro Bluetooth OBD2 adapter with a smartphone running the diagnostic app
A Bluetooth scanner such as the 3210Pro shows live data on your phone.

Live data shows the sensor readings as they change. Start the engine for this step if needed, and keep the car parked unless someone else is driving while you watch the screen. Never read a scanner while you're driving.

A few readings worth knowing:

  • Coolant temperature: should climb steadily as the engine warms up and then hold steady. If it never warms up properly, the thermostat may be stuck open (a common cause of code P0128).
  • Short-term and long-term fuel trims: show how much the computer is adding or removing fuel. Readings close to zero are normal. Large positive numbers mean it's adding fuel to make up for a lean mixture.
  • Engine RPM at idle: should be steady once warm. A hunting or rough idle can point to a vacuum leak or misfire.
  • Battery or system voltage: with the engine running, a healthy charging system typically shows around 13.5 to 14.5 volts. If it's close to battery voltage with the engine running, check the charging system.

Normal ranges vary by vehicle. Compare readings to the specifications in the workshop or owner's manual, and look for values that are clearly out of line or that don't change when they should.

Step 8: Check the readiness monitors

Readiness monitors (also called I/M readiness) are self-tests the engine computer runs on systems such as the catalytic converter, oxygen sensors, evaporative system and EGR. Each one shows as complete (ready) or incomplete (not ready).

Monitors reset to incomplete when codes are cleared or the battery is disconnected. They only complete again after the car has been driven through the right mix of conditions, which can take several days of normal driving.

Readiness is useful in two ways:

  • After a repair: once all monitors are complete with no codes returned, the repair has very likely held.
  • When buying a used car: several incomplete monitors on a car that has supposedly been driven normally can mean codes were cleared recently, possibly to hide a fault. See our used car inspection checklist.

Step 9: Clear codes safely

Clear codes only after you've recorded them and fixed (or at least understood) the cause. Clearing a code doesn't repair anything. If the fault is still there, the code and the light will come back.

  1. Confirm you've recorded the codes and freeze frame data.
  2. Ignition on, engine off.
  3. Select "Erase codes" or "Clear codes" and confirm.
  4. Turn the ignition off, wait a moment, then start the engine. The check engine light should stay off.
  5. Drive normally over the next few days, then scan again. Check for returning or pending codes, and check the readiness monitors are completing.

Times you should not clear codes:

  • Before a mechanic sees the car. They may want to see the fault while it's active.
  • With a flashing check engine light. The misfire is still happening. Get the car checked.
  • To get past an inspection. Cleared codes reset the readiness monitors, which is easy to spot.

When to stop and get help

  • Flashing check engine light: slow down, pull over when safe, and get the car checked before further driving.
  • Limp mode: if the car suddenly loses power, get off the road safely, then scan. See our limp mode guide.
  • Brake warnings: a red brake light or a brake fault means don't drive.
  • Airbag (SRS) light: reading the code is fine with a suitable scanner, but airbag repairs are for a qualified professional.
  • Temperature or oil pressure warnings: stop the engine as soon as it's safe to do so.

Which Autophix scanner do you need?

Every scanner in the range follows the steps above for engine codes. The differences are what else they read.

  • Check engine light only: the OM123 reads engine codes, live data, readiness, freeze frame and VIN across all five OBD2 protocols, for Australian vehicles from 2006. For Japanese-market imports with the 16-pin port, the OM127 adds JOBD.
  • Phone users: the 3210Pro shows engine codes and live data in an app, and reads ABS, airbag and transmission codes on some makes (Ford, GM, Chrysler, Toyota, Mercedes).
  • Touring: the Outback 9000 shows the likely cause of an engine code on screen, so you don't need reception to look it up.
  • Battery problems too: the BT500 Pro adds battery, cranking and charging tests.
  • ABS, airbag and service work: an all-system scanner for your brand, or the multi-brand DM5100 range. See professional scanners.

Be clear on the limits: the OM123, OM127, Outback 9000 and BT500 Pro read engine codes only. They won't read or clear an ABS or airbag light. Browse all OBD2 scanners.

Frequently asked questions

Where is the OBD2 port in my car?

Usually under the dash on the driver's side, within reach of the steering wheel. The SAE J1962 connector standard places it on the driver's side of the instrument panel, reachable from the driver's seat. Check behind small trim panels or near the fuse cover, or look up "diagnostic connector" in the owner's manual.

Should the engine be running when I scan?

For reading and clearing codes, turn the ignition on with the engine off. Live data is more useful with the engine running, so start it for that step, with the car parked and somewhere well ventilated.

Can I leave the scanner plugged in while driving?

Only if it can't interfere with the pedals or your view, and never read the screen while driving. A handheld scanner with a cable should be unplugged before you drive. Unplug any adapter if the car will be parked for a long time.

Will clearing the code turn off the check engine light for good?

Only if the fault has been fixed. Clearing erases the code and switches off the light, but if the cause is still there the computer will detect it again and the light will return.

Why are my readiness monitors showing "not ready"?

Monitors reset when codes are cleared or the battery is disconnected. They complete again after several days of normal driving through a mix of conditions. If they stay incomplete for weeks, have the car checked.

Can an OBD2 scanner read the ABS or airbag light?

A basic code reader can't. The 3210Pro reads ABS and airbag codes on some makes, and the brand-specific and multi-brand scanners read them on their supported brands.

Sources

Written by

Trevor Ryan, Director, Autophix

Trevor runs Autophix Australia from Melbourne. He has worked in the automotive industry for more than 20 years, has a passion for cars and 4WDing, and started Autophix Australia to make fault finding an easy DIY job.

Published · Last reviewed

This guide is general information. A scanner tells you where a fault is, not always why. If a warning light is flashing, the brakes or steering feel wrong, or you're not sure, stop safely and have the vehicle checked by a qualified mechanic.