The check engine light means your car's engine computer has found a fault, usually in the engine, ignition, fuel or emissions system, and stored a trouble code. A steady light means book it in soon. A flashing light means a serious misfire: stop when safe. Plug an OBD2 scanner into the port under the dash to read the code.

What the check engine light means
Every modern car has an on-board diagnostics system, known as OBD2. It watches the parts that affect how the engine runs and what comes out of the exhaust: sensors, injectors, ignition, the catalytic converter, the evaporative system that traps fuel vapour, and on diesels the particulate filter and EGR system.
When the computer sees a reading outside its limits, it stores a diagnostic trouble code (DTC) and, if the fault is confirmed, turns on the malfunction indicator lamp. That lamp is what most people call the check engine light or engine management light. It is usually amber and shaped like an engine, though some cars spell out "Check Engine" or "Service Engine Soon".
The light tells you that something is wrong. It does not tell you what. The stored code narrows it down, and that is why reading the code is the first job.
Steady or flashing: what each one means
| What you see | What it usually means | What to do |
|---|---|---|
| Light comes on briefly at start-up, then goes out | Normal bulb check. The system is working. | Nothing. |
| Steady light, car drives normally | A fault has been confirmed. Often a sensor, a loose fuel cap or an emissions fault. | Read the code, then book a service soon. Avoid long trips or heavy towing until you know the cause. |
| Steady light with power loss, noises, smoke or other warning lights | A fault that is affecting how the car runs. The car may be in limp mode. | Pull over when safe. Read the code or call roadside assistance. |
| Flashing light | A severe misfire that can overheat and damage the catalytic converter. | Ease off, get off the road safely and stop. Don't keep driving on a flashing light. |
Amber and red lights are different
An amber engine light is a warning that a fault needs checking. Red warning lights, such as engine temperature, oil pressure, brake or charging lights, signal a problem that needs prompt action. If a red light comes on with the engine light, stop when safe and switch off the engine. Check your owner's manual for what each symbol on your car means.
What to do when the check engine light comes on
- Check whether it is steady or flashing. If it is flashing, reduce speed and stop somewhere safe. A flashing light points to a misfire, and unburnt fuel can overheat the catalytic converter.
- Look at the other gauges. High engine temperature, low oil pressure or a red warning light means stop and switch off.
- Notice how the car is driving. Rough idle, hesitation, a strong fuel smell or sudden loss of power are clues worth noting for whoever repairs it.
- Check the fuel cap. If you filled up recently, make sure the cap is on and clicked tight. A loose cap can trigger an evaporative system code. The light will not go out straight away; it can take several drives.
- Read and record the code. Plug in an OBD2 scanner and write down or photograph every code, plus the freeze frame data if your scanner shows it.
- Decide on the next step. Use the code to judge whether the car is safe to drive to a workshop, or whether it needs a tow.
If you lose power suddenly and the car will not rev past a certain point, it is probably in limp mode. Get off the road safely first, then read the code. Our limp mode guide explains what to do next.
Common causes of a check engine light
Hundreds of faults can turn on the light, but a small group accounts for most of them:
- Loose, damaged or wrong fuel cap. The evaporative system tests itself for leaks, and a cap that doesn't seal will fail that test.
- Oxygen sensors. These measure oxygen in the exhaust so the computer can adjust the fuel mixture. They age, and contamination from oil or coolant shortens their life.
- Spark plugs and ignition coils. A worn plug or failing coil causes misfires. On a petrol engine this is the most common reason for a flashing light.
- Catalytic converter. Usually a result of something else, such as long-term misfires or oil burning, rather than a fault on its own.
- Mass airflow (MAF) sensor. Dust getting past a poorly sealed air filter can coat the sensor and upset its readings.
- Thermostat. A thermostat stuck open stops the engine reaching its normal temperature and sets a code. Cooling systems work hard in Australian summer heat.
- Diesel emissions parts. On diesels, a blocked particulate filter, a faulty pressure sensor or a sticking EGR valve are frequent triggers. See our DPF regeneration guide.
For what specific codes mean, such as P0420, P0300 or P0171, see our guide to OBD2 fault codes.
How to read check engine light codes yourself
You don't need a workshop to find out why the light is on. Any OBD2 code reader can pull the stored engine codes in a couple of minutes. The steps below work for most petrol and diesel cars sold in Australia from the mid-2000s on.
Find the OBD2 port
The port is a 16-pin, D-shaped socket. It is almost always within reach of the driver's seat, usually under the dash to the right or left of the steering column, near the bonnet release or behind a small cover panel. If you can't find it, check the owner's manual index under "diagnostic connector" or "OBD".

Read the code step by step
- Park on level ground with the engine off and the handbrake on.
- Plug the scanner cable firmly into the OBD2 port. On a Bluetooth scanner, plug in the adapter and pair it with the app on your phone.
- Turn the ignition to "on" without starting the engine, or start the engine if your scanner's instructions say to.
- Choose "Read codes" (sometimes labelled "DTC" or "Diagnose") from the menu.
- Write down or photograph every code shown, including any marked "pending".
- Open the freeze frame screen and record that too. It is a snapshot of engine speed, temperature, load and other values at the moment the fault was set.
- Check the readiness (I/M) monitors. They show which self-tests the car has completed since codes were last cleared.
- Look up each code before you decide to clear anything.
Our step-by-step guide to using an OBD2 scanner covers each screen in more detail.
What the code tells you
Engine codes start with the letter P (powertrain) followed by four characters. A code starting P0 is a generic code with the same meaning on every make. A code starting P1 is defined by the manufacturer, so the description depends on your vehicle. For example, P0301 means a misfire has been detected in cylinder 1 on any car that sets it.
Treat the code as the starting point of a diagnosis, not the answer. A code for a lean mixture, for example, could come from a vacuum leak, a dirty MAF sensor or a weak fuel pump. The freeze frame and live data help narrow it down, and a mechanic may still need to test parts before replacing them.
Pending and confirmed codes
A pending code means the computer has seen a fault once but has not confirmed it yet. It may not have turned on the light. If the same fault shows up again on a later drive, the code is confirmed and the light comes on. Pending codes are useful early warnings, especially before a long trip.
Should you clear the code?
Only after you have recorded it, and ideally after the fault is fixed. Clearing codes erases the freeze frame data a mechanic would use, and resets the readiness monitors so the car has to rerun its self-tests. If the fault is still there, the light will come back.
Australian motoring clubs advise against simply resetting the light to make it go away, because that hides the symptom rather than fixing the cause. If you have tightened a loose fuel cap or replaced a faulty part, clearing the code and watching whether it returns is a reasonable check. Many cars need a few normal drives, sometimes around a week of regular use, before all the readiness monitors are complete again.
Check engine lights on the road and in the bush
A light that would be a minor nuisance in the city needs more thought when you are towing a van or 500 km from the nearest town.
- Corrugations and vibration. Hours on rough roads can loosen electrical connectors and vacuum hoses. A sensor circuit code or a sudden lean code after a corrugated stretch is worth checking at the plug and hose before assuming the part has failed.
- Dust. Fine dust that gets past the air filter can foul the MAF sensor. Check the airbox seal and filter if you see airflow or lean codes after dusty tracks.
- Heat and towing. Hot days and heavy loads push coolant and transmission temperatures up. Watch the temperature gauge closely if any warning light comes on while towing.
- Diesel 4WDs. Low-speed off-road driving and short trips don't give the particulate filter the sustained running it needs to clean itself. Diesel filter and EGR codes are common on touring vehicles.
- Remote travel. A code reader in the glovebox lets you see the code on the spot, record it, and decide whether to keep going gently to the next town or call for help. If the light is flashing or the car is in limp mode, stop and get advice before going on.
When to stop driving and see a mechanic
Use the code to inform the decision, but these signs mean stop or get professional help, whatever the scanner says:
- The check engine light is flashing.
- The temperature gauge is high, or the oil pressure or charging light is on.
- The car has gone into limp mode, with sudden loss of power. Get off the road safely.
- The brake warning light is on, or the brakes feel different. Don't drive with a brake fault.
- The airbag (SRS) light is on. Airbag systems should only be worked on by a qualified technician.
- You smell fuel, see smoke or hear new knocking or grinding noises.
- The same code keeps coming back after a repair.
If you are a member of a motoring club, many roadside patrols carry diagnostic tools and can advise whether the car is safe to drive or needs a tow.
Which Autophix scanner do you need?
To find out why a check engine light is on, a basic engine code reader is enough. Every scanner in our range reads engine codes. What changes is the screen, extra tests, and whether it can read other systems like ABS and airbags.
| Scanner | Best for | Limits |
|---|---|---|
| OM123 code reader | Reading and clearing engine codes, live data, freeze frame and readiness on most Australian vehicles from 2006 | Engine codes only |
| OM127 code reader | As the OM123, plus JOBD for Japanese-market imports with a 16-pin port | Engine codes only |
| Outback 9000 | Glovebox scanner for touring, with a colour screen and rubber cover. Shows the likely cause on screen. Basic voltage check. | Engine codes only |
| 3210Pro Bluetooth | Engine codes and live data on your phone. ABS, airbag and transmission codes on some makes (Ford, GM, Chrysler, Toyota, Mercedes). | Other systems on those makes only |
| BT500 Pro | Engine codes plus a full battery, cranking and charging test | Engine codes only for diagnostics |
If you want to go further than engine codes, such as reading every module, DPF regeneration or service resets, look at the brand-specific scanners in our professional scanners range. Nissan owners should look at the DM5100-2.
A scanner tells you where to look. It won't fix the fault, and some faults still need workshop tools and testing. You can compare the full range in our OBD2 scanners collection.


Frequently asked questions
Can I drive with the check engine light on?
If the light is steady and the car drives normally, you can usually drive it carefully to a workshop, but get the code read soon and avoid long trips or towing until you know the cause. If the light is flashing, or there are other warning lights, power loss or overheating, stop when it is safe.
Will the check engine light turn off by itself?
Often, yes. If the fault goes away, such as after tightening a loose fuel cap, the computer will usually turn the light off after several fault-free drives. The code stays stored in memory for a while, so a scanner can still show what happened.
Does disconnecting the battery reset the check engine light?
On many cars it clears the codes, but it also erases the freeze frame and readiness data and can reset radio, window and idle settings. If the fault is still there, the light will come back. Reading and clearing codes with a scanner is the better way to do it.
Why did my check engine light come on after filling up?
The most common reason is a fuel cap that isn't fully tightened or has a worn seal. The evaporative system detects the leak and sets a code. Tighten the cap until it clicks. The light may take several drives to go out.
Can a cheap code reader tell me exactly what part to replace?
No scanner can do that on its own. A code points to the system or circuit where the fault was detected. Freeze frame and live data help narrow it down, but a part should be tested before it is replaced.
Is a check engine light an automatic roadworthy fail?
Requirements differ between states and inspectors, so check with your state transport agency or a licensed tester. Either way, it is worth fixing the fault and confirming the light stays off before an inspection.